3DPrinting

15625 readers

219 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago

MODERATORS

andypiper@lemmy.world

henry_rowengartner@lemmy.world

j4k3@lemmy.world

GrayBackgroundMusic@lemm.ee

Upgraded Ender 3v2 Issues (sh.itjust.works)

submitted 10 months ago by xzot746@sh.itjust.works to c/3dprinting@lemmy.world

20 comments fedilink hide all child comments

I've had an Ender 3 v2 for a few years now and have had mostly no issues. I've upgraded the hot end to a microswiss direct drive and a dual z setup (twin z steppers on a shared cable).

Recently started having issues with the 4.2.2 board and replaced it with a BTT mini SKR 3 v3.

Since I've put the new board in, I am having troubles getting the bed to level and stay level.

The height profile of the bed is now showing a dip in the centre (which was not there before). When I run a print it seems to be overcompensating for the dip. If I level the bed with the corner screws and don't use the bed mesh then it prints fairly good, but after a few prints the bed goes out of level again.

I can't seem to make any adjustments that help the issue. Yesterday tightened up all the screws (silicon spacers instead of springs). Releveled the bed and had a small dip in the middle and an overall height difference of 0.170 across the bed (normal prior to this was 0.310). Sent a print with bed mesh and mostly came out good.

Went to fire up a new print today and the bed height is showing 0.830 overall difference.

I'm not sure if it is a BL touch issue (the BL touch is a v3.1 and is original with a single 5 wire connector plugged into mini SKR) dual z issue (disconnected 1 in an attempt to level and didn't see much difference, the BTT has two connectors for dual z but run off one stepper driver as I understand it, I am using the y cable for only one stepper motor, while the other motor has its own cable).

I use klipper with a RPi zero 2 w.

I just can't seem to figure out that has been causing the issue since the board swap.

Anyone have some ideas as where to point me?

you are viewing a single comment's thread
view the rest of the comments

[–] xzot746@sh.itjust.works 1 points 10 months ago

I did a probe accuracy test yesterday, 0.002. So I think it's good.

I have the entire printer torn right back to square one. Will double check everything as I reassemble.

Did a couple prints yesterday with no BL touch, bed level the four corners, seemed good a bit of first layer micro adjustments.

Went to perform another print (same as the previous print) and the bed was out of whack again. The bed level test said that the right side was out half a turn on the knobs.

I'm starting to think it has to do with the dual z motors and not staying timed or level with each other.

Will see how it works once I get it all back together.

Thanks.